DYSCO
Industrial instrumentation — DYSCO EP

03 / DYSCO EP SERVICES

INDUSTRIAL PROCESS
INSTRUMENTATION

Engineering, supply, installation and maintenance of pressure, temperature, level and flow instruments. We configure signals, verify loops and connect data to control systems and cloudLOGGER SCADA.

ENERGY PULSE ⌄

REFERENCE DATA / U.S. EIA

WTI CRUDE—USD / BARREL
HENRY HUB GAS—USD / MMBtu

Open the panel to view the data.

EIA SOURCE ↗

Published daily reference, not a real-time quote. Check the date of each value.

← ALL SERVICESENGINEERING / FIELD / TECHNOLOGY

SCOPE / INDUSTRIAL INSTRUMENTATION

INSTRUMENTS, LOOPS
AND CONTROL VALVES.

Measurement services from the process connection to the PLC, DCS or SCADA: selection, configuration, reference adjustments, testing and rehabilitation. We consider fluid, materials, connections and installation conditions.

01

Pressure, temperature, level and flow

Selection and supply of electronic instrumentation for separators, metering points, plants, compressors and turbines. Required range, process conditions, materials and compatibility with the existing system are reviewed.

02

Loop testing and configuration

Checks of power, wiring, scaling, units, signals and communications. Instrument configuration, reference adjustments, functional testing and commissioning follow defined procedures and criteria.

03

Valves and maintenance

Diagnostics and rehabilitation of valves, actuators and positioners; maintenance of pneumatic, hydraulic and electronic instrumentation. We record interventions and verify loop behavior after the work.

Engineering, supply, installation, commissioning, operation and maintenance.

Instrument and signal documentation

Scope may include instrument identification, signal lists, configuration, test records and updated documentation. ANSI/ISA-5.1 provides a reference for symbols and identification in instrumentation and control documents.

Sensors monitored through cloudLOGGER

We integrate measurements with a PLC, gateway or RTU and cloudLOGGER SCADA, subject to confirmed interfaces. Trends, alarms, inventory and installation, maintenance or calibration records link each variable to its instrument and service history.

Calibration and measurement management

Configuration, reference adjustment and documented calibration are distinct activities. ISO 10012 addresses measurement process and equipment management; ISO/IEC 17025 addresses laboratory competence. Accredited scope, uncertainty and certificate traceability must be verified in the supporting documents.

Applicable standards and editions are defined in the engineering and contracted scope. Referencing a standard does not certify the company, equipment or installation.

FREQUENTLY ASKED QUESTIONS

TECHNICAL QUESTIONS
AND SERVICE SCOPE.

Which process variables do you work with?

We work with pressure, temperature, level and flow instrumentation according to site conditions.

Do you work with control valves?

Yes. We diagnose, rehabilitate and adjust valves, actuators and positioners within the defined scope.

Which industrial communication protocols do you integrate?

We work with protocols such as HART, Modbus and Foundation Fieldbus according to existing equipment and system capabilities.

How is a process instrument selected?

Selection considers the variable, range, fluid, operating pressure and temperature, materials, connection, power supply and protocol, checked against process requirements and conditions.

Does a reading problem always require replacing the instrument?

Not necessarily. Diagnosis checks power, configuration, signal, communication and the loop to identify the cause before deciding on adjustment, repair or replacement.

What does a loop review include?

Depending on scope, the review checks the signal path from the instrument to control or supervision, its configuration and interpretation, and the response of the components involved.

How are instruments monitored through cloudLOGGER?

We define the instrument interface and its link to a PLC, RTU or gateway. cloudLOGGER SCADA receives compatible variables for displays, trends and alarms, and can organize asset records and interventions.

Is a reference adjustment the same as accredited calibration?

No. Adjustment changes or configures response; calibration documents the relationship to references under defined conditions. Where accreditation is required, the laboratory, quantity, range and accredited scope must be checked in the relevant certificate.

THE NEXT STEP / LET'S TALK

REQUEST AN INDUSTRIAL
ENGINEERING PROPOSAL.

Let us review your equipment, variables and requirements for SCADA, automation, instrumentation, safety or measurement.

OUR BASE18.143° N / 94.443° W

DYSCO EP IN
COATZACOALCOS, MEXICO.

Tamaulipas 407 · Col. Petrolera
ZIP 96500 · Veracruz, Mexico

GET DIRECTIONS ↗

Projects related to this service

↑

COOKIES AND PRIVACY

You can accept maps and analytics separately. Your choice is remembered for 180 days and can be changed here at any time.

Read the privacy notice ↗

Search the site